Measurement of Spiral Chute Pitch

Measurement of Spiral Chute Pitch

Measurement of the pitch of a spiral chute: 1. Introduction to the beneficiation chute, including the inclined flow separation process. Mineral mortar is applied to a partially inclined chute or inclined surface. With the assistance of flowing water, the mineral particle group is not tightly fastened and layered. The upper part of the light mineral material quickly flows out of the groove, while the lower part of the heavy mineral material stagnates in the inner groove or slowly flows out from the lower part. After distinguishing and connecting, the concentrate and tailings can be obtained. Spiral chutes are machinery for mining and beneficiation, especially ideal for sand mining in coastal areas, riverbanks, sandbanks, and streams. The product also has the characteristics of reasonable structure, simple installation, small land occupation, simple operation, stable beneficiation, clear screening of ore, large production capacity, high efficiency, high beneficiation enrichment ratio, high recovery probability, and stable operation. It has the advantages of light weight, moisture prevention, rust prevention, strong corrosion resistance, and strong applicability to feed volume and density, Granularity, and grade fluctuation. 2、 The mineral mortar with the same technical principle is slowly fed to the surface of the spiral groove through the feeding groove installed at the end of the rotating groove head, and then selected for operation. The bottom of the rotating groove is equipped with a valve block type equipment selection groove, which divides the sorted products into three categories according to grade along the radial direction. By adjusting the position of the valve block to change the acquisition width of each device, the product gathering hopper allows the intercepted variable mineral flow to be converged and exported separately. The transverse plane of the fiberglass spiral chute is particularly suitable for the separation of fine ore materials when the slope of the curve changes. Measurement of the pitch of the spiral chute at the rate of . Features: The fiberglass spiral chute has attracted special attention among many gravity separation machines due to its low power consumption, simple structure, small land occupation, simple operation, stable beneficiation, clear mineral sorting, no moving parts, convenient maintenance and management, strong processing capacity per unit area, and other characteristics. The machinery has a wider and smoother groove surface, and the area where the mortar presents laminar flow is huge, making it more suitable for handling medium to fine (-4mm) particle sized ores. China has produced spiral concentrators with diameters of 400, 600, 900, and 1200mm, Ф The processing capacity of 1200MM four head is about 4-6 tons per hour. The measurement of the pitch of the spiral chute is made up of six parts: a feeding homogenizer, a feeding chute, a spiral groove, an equipment selection groove, a product gathering hopper, and a groove bracket (including a cross or triangular frame). The rotating groove connected by spiral blades is a key component. The rotating plate is made of fiberglass (fiber reinforced coal gangue), connected together by screws, and the spiral groove has a pre made wear-resistant layer on the selected surface. She has the advantages of being lightweight, sturdy, and durable consumables that are not easily damaged. Above the rotating groove, there is a multi tube feeding homogenizer for ore separation, which is simple and convenient to control. The sieving mineral containers are freely stacked on the cross (or tripod) of the support table. The evenly distributed mortar is slowly fed onto the surface of the rotating groove through the feeding groove installed at the head of the spiral groove, and sorting is carried out. The tail end of the spiral groove is equipped with a valve block type new equipment to obtain the groove. The selected new products are divided into three categories (or four types) according to grade along the radial direction. Change the cutting width of each new equipment by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that allows the selected multiple ore streams to converge and lead out separately. The slope change of the cross-section and curve of the spiral concentrator is very suitable for the separation of fine particle materials. 5、 The fiberglass spiral chute is suitable for processing 0.6-0.03mm and vein ore as well as sand ore, but it is unfavorable for sorting when the mud content is high. Nowadays, it has been widely used for processing iron ore, tungsten, tin ore, tantalum niobium ore, coastal and riverbed ore, or gold ore. Measurement of Spiral Chute Pitch Measurement of Spiral Chute Pitch

Measurement of Spiral Chute Pitch